Green Horizons

Volume 16, Number 4
Fall 2012

Forestry 101: Soft Hardwood, Hard Softwood (and vice versa)
Chuck Ray, Penn State Extension (edited slightly from Chuck’s original blog)

Softwood is soft...hardwood is hard. Right?

No, not really. This is by far the most common misconception non-woodites have about wood when they browse the aisles at the Big Box. And you have to ask "Well, why do they call them that, anyway?"

The most likely reason has to do with logging back in the old days. Farmers clearing their land in the east back in the18th and 19th centuries would have encountered a great range of deciduous trees, scientifically categorized as angiosperms,those that have broad leaves, true flowers, have their seeds enclosed in a fruit, and shed their leaves in the fall (they are deciduous). The soil of the northeastern part of North America was typically thick and rich in the valleys,because of the ancient age of the Appalachian Mountain sand the temperate climate that inhibited frequent and large wildfires. The result was a widely ranging deciduous forest, and the varied species that made them up consisted of a large percentage of oak, hickory, and maple.

Now, the folks that were out there clearing all these oak,hickories, and maples with axes and two-man saws, and shaping them for utensils with draw knives, found them pretty tough customers. The oaks and hickories, in particular,are heavy woods, going from about 80 to 90 pounds per cubic foot when green. And the folks down south, who were harvesting live oaks for ship timbers and bows, really had a chore...live oak is the heaviest hardwood in North America, running well over 100 pounds per cubic foot when green.

Apparently, these "heavy" species (technically, the ones with the highest "density") left enough of an impression on these early pioneers that they generally thought of these deciduous angiosperms as "hard" wood, even though other species, such as cottonwood, aspen, American elm, and American chestnut, which were common back in those days, were quite a bit lighter. The aptly named cottonwood weighs less than 40 pounds per cubic foot when green, and whittles easily with a dull pocket knife, as I found out along time ago.

Now, those old-timers generally didn't talk about different woods like scientists. They didn't have time or mental energy to waste thinking about the relative variability of wood properties expressed in different angiosperms at different moisture contents or growth rates. They just knew that the deciduous trees really wore out their saws and axes,and their muscles...so they got in the habit of calling them"hardwoods".

As opposed to the gymnosperms, which are those cone bearing(coniferous) trees that have needles and retain them in the winter. Most of the coniferous trees in the Northeast are fairly light species; the famous eastern white pine,which was the favorite of the King's navy back in colonial days for its straight, light, yet strong wood, and made perfect masts for their ships, is only slightly heavier than cottonwood at about 40-45 pounds per cubic foot when green.Eastern hemlock (the state tree of Pennsylvania), is just a tad heavier, at 45-50 pounds. Eastern red cedar would have been the heaviest coniferous tree the settlers of the Northeast typically wrestled with, at about 55-60 pounds per cubic foot. Naturally, then, when they compared the heaviest Northeastern conifers with hickories or oaks, the conifers seemed light by comparison, and so became "softwoods" Ianthe local vernacular.

But as we spread out into the rest of the country, our common man's classification system started to break down. As we harvested the Lake States to build Chicago, Milwaukee,and Detroit, we found that aspen was a pretty "soft"hardwood. And early settlers out west found abundant red alder, a light-weight hardwood that has somewhat the look,weight, and feel of western redcedar.

A logging crew from East Perry Lumber Company has been recognized by the Missouri Department of Conservation (MDC) as "Missouri Logger of the Year." This award recognizes a person or crew that practices sustainable forest management. East Perry's three-man crew consists of Tim Schmidt, Adam Hoehn and Ron Stelling.

Microscopic view of southern pine.
Koch, P. 1972a. Utilization of the southern pines. I. The raw material. USDA Forest Service Agricultural Handbook No. 420. 733 pp.

But the folks harvesting the southern U.S. were really confused, because not only did they find the super-light"hardwood" species basswood and cottonwood, but they found some of the continent's heaviest softwood, of which four species, long leaf, slash, short leaf, and loblolly, are now marketed under the unifying moniker of southern yellow pine. Southern pine not only has a relatively high density when dry (try driving a nail into a southern pine stud with ten or more growth rings per inch, and you'll bend a few nails) but it also has a resinous "pine tar" that served navies well in the wooden ship days (naval stores were buckets of pine tar and turpentine that were used to caulk seam sand cracks in hulls, and seal wood from moisture), and this pine tar, or "pitch" retained moisture in the stem and added even more weight to the wood. Resultantly, old southern pine trees could yield pitch-filled logs that could weigh 90to 100 pounds per cubic foot green even though the "specific gravity", the weight of a wood species relative to the weight of water, is quite a bit lower than those tough old oaks and hickories.

As you can see in the above picture of southern pine cell structure, softwoods are comprised of long, thin tubular cells, and it is these that carry the water through the stem of the tree. It is this uniformity, in addition to the density of the wood that makes softwoods seem relatively soft when being sawn or machined.

On the other hand, the moisture is transported in hardwoods through larger diameter pores, or vessels. These come in different shapes, sizes, and locations in the different hardwood species, and this variation contributes to the woodworkers sense that certain hardwoods are rough, or"hard" to machine.

Microscopic view of white oak.
http://classes.mst.edu/ide120/lessons/
wood/cell_structure/index.html

Nowadays, wood "hardness" is complicated (or, depending on your point of view, simplified) further by hardness standards developed and adopted for wood grading for different products. The most commonly used hardness metric used in the various wood industries is the "Janka-ball" hardness test, which measures the resistance of the surface of a wood species to depression when a metal ball is dropped from a specified distance onto the surface of the wood. These standardized results are then used as a relative measure of the hardness of a wood, the results of which are fairly easy to find, such as at this Wikipedia page. If you browse the Janka hardness table, you'll see that the hardest woods are tropical hardwood species, but then below that, softwoods and hardwoods are relatively randomly mixed.

So, now you know the rest of the story...that hardwoods aren't necessarily hard, and softwoods aren't necessarily soft, and why. So next time, don't go wandering into Home Depot and start asking questions that make you look like a wood neophyte; do what I do, and pretend to actually know what you're talking about.


[ Back to Articles ]